Running programs with the MIPS user-mode emulator fails during dynamic
loading, as floating-point instructions are not enabled in in
env->hflags. Move the code for doing so from fpu_init to cpu_reset so
the MIPS_HFLAG_{FPU,F64} setting doesn't get clobbered by cpu_reset
setting env->hflags to MIPS_HFLAG_UM.
The same end can be achieved by swapping the ordering of fpu_init and
cpu_reset in cpu_mips_init, but it seemed better to consolidate the
CONFIG_USER_ONLY code into a single location.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The CPUID features QEMU presented to the guest were not up-to-date
with QEMU's emulated feature set.
Add the missing bits of recent (and not so recent) additions to
QEMU's emulation engine.
For stability reasons only the user mode usable bits are exposed for
now, features like Monitor or CR8LEG are left out.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
1. Add correct definitions of error numbers.
2. Implement SYS_osf_sigprocmask
3. Implement SYS_osf_get/setsysinfo for IEEE_FP_CONTROL.
This last requires exposing the FPCR value to do_syscall.
Since this value is actually split up into the float_status,
expose routines from helper.c to access it.
Finally, also add a float_exception_mask field to float_status.
We don't actually use it to control delivery of exceptions to
the emulator yet, but simply hold the value that we placed there
when loading/storing the FPCR.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The only thing to do here is to expose the current processor mode to GDB
and to set the processor mode properly when we change the PC.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
There's no good way to add this incrementally, so we do it all at once.
The only changes to shared code are in handle_delay_slot. We need to
flip ISAMode when doing a jump-and-exchange. We also need to set
ISAMode the low bit of the target address for jump-to-register.
Also, since we're now adding bits that can be in MIPS_HFLAG_BMASK_EXT,
make sure we use MIPS_HFLAG_BMASK_BASE in the places where we just want
basic information about a branch.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Move delay slot handling to common code whose invocation can be
controlled from gen_intermediate_code_internal.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This is a common pattern in existing code. We'll also use it to
implement the mips16 SAVE/RESTORE instructions.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
It's easier to implement mips16 shift instructions if we're not
examining the opcode inside gen_shift_{imm,}. So move ROTR and ROTRV
and do the special-case handling of SRL and SRLV inside decode_opc.
Likewise for their 64-bit counterparts.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We need to stash the operating mode into the low bit of the error PC and
restore it on return from interrupts.
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
We create separate masks for the "basic" branch hflags and the
"extended" branch hflags and define MIPS_HFLAG_BMASK as the logical or
of those two. This is done to avoid churning the codebase in lots of
different places.
We also make the execution mode an hflag under MIPS_HFLAG_TMASK
Signed-off-by: Nathan Froyd <froydnj@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This is a workaround only, and is a partial revert
of a few changes to BMDMAState which removed pci_dev
field on the way.
- cmd646 pci_from_bm() expects bm->unit value to
correspond with bm data being passed to callback
as opaque pointer. This breaks when write to dma
control register of second channel happens when no
dma operation is in progress, so bm->unit is zero
for second channel, and pci_from_bm() returns garbage
pointer. Crash happens shortly after that while
dereferencing that pointer.
v0->v1: cleaned up dead code from pci_from_bm.
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
s390 code has an obvious typo, which results in:
hw/s390-virtio.c: At top level:
hw/s390-virtio.c:249: error: request for member ‘no_vga’ in something not a structure or union
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Building on 32 bit host we get:
hw/s390-virtio.c: In function ‘s390_init’:
hw/s390-virtio.c:184: error: integer constant is too large for ‘unsigned long’ type
64 bit values must be ULL.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Don't define C99 math functions on OpenSolaris (Solaris 11),
which still ships GCC 3.4.3. This fixes redefinition warnings.
Spotted by Palle Lyckegaard.
Signed-off-by: Andreas Färber <afaerber@opensolaris.org>
Cc: Palle Lyckegaard <palle@lyckegaard.dk>
Cc: Ben Taylor <bentaylor.solx86@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Avoid an unresolved symbol error for TFR,
which is defined in sysemu.h.
Based on patch by Palle Lyckegaard.
Signed-off-by: Andreas Färber <afaerber@opensolaris.org>
Cc: Palle Lyckegaard <palle@lyckegaard.dk>
Cc: Ben Taylor <bentaylor.solx86@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Stepping through the SS-5's OBP initialization routines
it looks like reading fdc main status register should
clear the fd interrupt.
The patch doesn't fix problems with fdc on sparc platform,
it only fixes fdc detection.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Implement a stub for the AFX register on SparcStation-5.
This stub is needed for running the original SS-5 OBP
instead of OpenBIOS (which allows to boot Solaris 2.5.1
and Solaris 2.6 kernels).
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
According to the SCSI-2 specification,
http://ldkelley.com/SCSI2/SCSI2/SCSI2/SCSI2-08.html#8.2.5 ,
"if the allocation length of the command descriptor block (CDB) is too
small to transfer all of the parameters, the additional length shall
not be adjusted to reflect the truncation."
The 36 mandatory bytes of response are written to outbuf, and then
only the length requested in CDB is transferred.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Currently, the msrs involved in setting up pvclock are not saved over
migration and/or save/restore. This patch puts their value in special
fields in our CPUState, and deal with them using vmstate.
kvm also has to account for it, by including them in the msr list
for the ioctls.
This is a backport from qemu-kvm.git
[v2: sucessfully build without kerneldir ]
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Return a QDict with server information. Connected clients are returned
as a QList of QDicts.
The new functions (vnc_qdict_remote_addr(), vnc_qdict_local_addr() and
put_addr_qdict()) are used to insert 'host' and 'service' information
in the returned QDict.
This patch is big, but I don't see how to split it.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Return a QDict with information about the just added device.
This commit should not change user output.
Please, note that this patch does not do error handling
conversion. In error conditions the handler still calls
monitor_printf().
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Each device is represented by a QDict. The returned QObject is a QList
of all devices.
This commit should not change user output.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Each device statistic information is stored in a QDict and
the returned QObject is a QList of all devices.
This commit should not change user output.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Each block device information is stored in a QDict and the
returned QObject is a QList of all devices.
This commit should not change user output.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Return a QDict, which may contain up to more two QDicts, depending
on the type of migration we're performing.
IMPORTANT: as a QInt stores a int64_t integer, RAM values are going
to be stored as int64_t and not as uint64_t as they are today. If
this is a problem QInt will have to be changed.
This commit should not change user output.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Each mouse is represented by a QDict, the returned QObject is a QList of
all mice.
This commit should not change user output.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
snprintf() is used because the UUID_FMT is too complex for
qobject_from_jsonf().
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
All 'info' commands should use QDict, this commit also kills
monitor_print_qobject() as do_info_version() doesn't use it
anymore (and no handler will).
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
While there update the documentation as well.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Should return a QDict and should not print the user protocol bits
(eg. "c|cont").
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Monitor commands should always return values in bytes and info
commands should always return a QDict.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
A helper function to get a QList from a QDict.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
This is a helper function that does type checking before retrieving
a QBool from the dictionary.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Other subsystems will need to link against them.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Nathan Froyd
Andre Przywara
Richard Henderson
Igor V. Kovalenko
Michael S. Tsirkin
Blue Swirl
Andreas Färber
Artyom Tarasenko
Edgar E. Iglesias
Paul Hartke
Glauber Costa
Luiz Capitulino