The NPCM7xx chips have multiple GPIO controllers that are mostly
identical except for some minor differences like the reset values of
some registers. Each controller controls up to 32 pins.
Each individual pin is modeled as a pair of unnamed GPIOs -- one for
emitting the actual pin state, and one for driving the pin externally.
Like the nRF51 GPIO controller, a gpio level may be negative, which
means the pin is not driven, or floating.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The NPCM730 and NPCM750 chips have a single USB host port shared between
a USB 2.0 EHCI host controller and a USB 1.1 OHCI host controller. This
adds support for both of them.
Testing notes:
* With -device usb-kbd, qemu will automatically insert a full-speed
hub, and the keyboard becomes controlled by the OHCI controller.
* With -device usb-kbd,bus=usb-bus.0,port=1, the keyboard is directly
attached to the port without any hubs, and the device becomes
controlled by the EHCI controller since it's high speed capable.
* With -device usb-kbd,bus=usb-bus.0,port=1,usb_version=1, the
keyboard is directly attached to the port, but it only advertises
itself as full-speed capable, so it becomes controlled by the OHCI
controller.
In all cases, the keyboard device enumerates correctly.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The RNG module returns a byte of randomness when the Data Valid bit is
set.
This implementation ignores the prescaler setting, and loads a new value
into RNGD every time RNGCS is read while the RNG is enabled and random
data is available.
A qtest featuring some simple randomness tests is included.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The watchdog is part of NPCM7XX's timer module. Its behavior is
controlled by the WTCR register in the timer.
When enabled, the watchdog issues an interrupt signal after a pre-set
amount of cycles, and issues a reset signal shortly after that.
Reviewed-by: Tyrone Ting <kfting@nuvoton.com>
Signed-off-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: deleted blank line at end of npcm_watchdog_timer-test.c]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This allows us to reuse npcm7xx_timer_pause for the watchdog timer.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This patch sets min_cpus field for xlnx-versal-virt platform,
because it always creates XLNX_VERSAL_NR_ACPUS cpus even with
-smp 1 command line option.
Signed-off-by: Pavel Dovgalyuk <pavel.dovgalyuk@ispras.ru>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 160343854912.8460.17915238517799132371.stgit@pasha-ThinkPad-X280
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
When compiling with -Werror=implicit-fallthrough, gcc complains about
missing fallthrough annotations in this file. Looking at the code,
the fallthrough is very likely intended here, so add some comments
to silence the compiler warnings.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-id: 20201020105938.23209-1-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The note test requires gcc 10 for -mbranch-protection=standard.
The mmap test uses PROT_BTI and does not require special compiler support.
Acked-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-13-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Use the new generic support for NT_GNU_PROPERTY_TYPE_0.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-12-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is generic support, with the code disabled for all targets.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-11-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is slightly clearer than just using strerror, though
the different forms produced by error_setg_file_open and
error_setg_errno isn't entirely convenient.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-10-richard.henderson@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
This is a bit clearer than open-coding some of this
with a bare c string.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-9-richard.henderson@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
For BTI, we need to know if the executable is static or dynamic,
which means looking for PT_INTERP earlier.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-8-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The second loop uses a loop induction variable, and the first
does not. Transform the first to match the second, to simplify
a following patch moving code between them.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-7-richard.henderson@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fixing this now will clarify following patches.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-6-richard.henderson@linaro.org
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Fix an unlikely memory leak in load_elf_image().
Fixes: bf858897b7 ("linux-user: Re-use load_elf_image for the main binary.")
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-5-richard.henderson@linaro.org
Message-Id: <20201003174944.1972444-1-f4bug@amsat.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
These are all of the defines required to parse
GNU_PROPERTY_AARCH64_FEATURE_1_AND, copied from binutils.
Other missing defines related to other GNU program headers
and notes are elided for now.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-4-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Transform the prot bit to a qemu internal page bit, and save
it in the page tables.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-3-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
The kernel sets btype for the signal handler as if for a call.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20201021173749.111103-2-richard.henderson@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
* Fix for Xen dummy cpu loop (which happened due to qtest accel rework)
* Introduction of the generic device fuzzer
* Run more check-acceptance tests in the gitlab-CI
-----BEGIN PGP SIGNATURE-----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=ZpMy
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/huth-gitlab/tags/pull-request-2020-10-26' into staging
* qtest fixes (e.g. memory leaks)
* Fix for Xen dummy cpu loop (which happened due to qtest accel rework)
* Introduction of the generic device fuzzer
* Run more check-acceptance tests in the gitlab-CI
# gpg: Signature made Mon 26 Oct 2020 09:34:04 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* remotes/huth-gitlab/tags/pull-request-2020-10-26: (31 commits)
tests/acceptance: Use .ppm extention for Portable PixMap files
tests/acceptance: Remove unused import
test/docker/dockerfiles: Add missing packages for acceptance tests
tests/acceptance: Enable AVOCADO_ALLOW_UNTRUSTED_CODE in the gitlab-CI
test/acceptance: Remove the CONTINUOUS_INTEGRATION tags
tests/acceptance/ppc_prep_40p: Fix the URL to the NetBSD-4.0 archive
scripts/oss-fuzz: ignore the generic-fuzz target
scripts/oss-fuzz: use hardlinks instead of copying
fuzz: register predefined generic-fuzz configs
fuzz: add generic-fuzz configs for oss-fuzz
fuzz: add an "opaque" to the FuzzTarget struct
fuzz: Add instructions for using generic-fuzz
scripts/oss-fuzz: Add crash trace minimization script
scripts/oss-fuzz: Add script to reorder a generic-fuzzer trace
fuzz: add a crossover function to generic-fuzzer
fuzz: add a DISABLE_PCI op to generic-fuzzer
fuzz: Add support for custom crossover functions
fuzz: Add fuzzer callbacks to DMA-read functions
fuzz: Declare DMA Read callback function
fuzz: Add DMA support to the generic-fuzzer
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
A default value is provided for the variable 'bitmap_name' to avoid
a compiler warning.
The compiler showed the warning:
migration/block-dirty-bitmap.c:1090:13: warning: ‘bitmap_name’
may be used uninitialized in this function [-Wmaybe-uninitialized]
g_strlcpy(s->bitmap_name, bitmap_name, sizeof(s->bitmap_name));
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Reported-by: Euler Robot <euler.robot@huawei.com>
Signed-off-by: Chen Qun <kuhn.chenqun@huawei.com>
Message-Id: <20201014114430.1898684-1-kuhn.chenqun@huawei.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
[eblake: commit message grammar tweaks]
Signed-off-by: Eric Blake <eblake@redhat.com>
sectors_per_chunk is a 64 bit integer, but the calculation is done in 32
bits, leading to an overflow for coarse bitmap granularities.
If that results in the value 0, it leads to a hang where no progress is
made but send_bitmap_bits is constantly called with nr_sectors being 0.
Signed-off-by: Stefan Reiter <s.reiter@proxmox.com>
Message-Id: <20201021144456.1072-1-s.reiter@proxmox.com>
Fixes: b35ebdf07 migration: add postcopy migration of dirty bitmaps
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[eblake: Use correct type for 8ULL, use () to avoid overflow]
Signed-off-by: Eric Blake <eblake@redhat.com>
This includes:
- Improvements to logging output
- Hypervisor instruction fixups
- The ability to load a noMMU kernel
- SiFive OTP support
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE9sSsRtSTSGjTuM6PIeENKd+XcFQFAl+S8zUACgkQIeENKd+X
cFR79wf/UjQulwFofCgOh8Fsrh5tlbRVYSXEHCWkEg6V8yfA+WYkkup94wBJK0V6
tJglht7v8aovUFWRyEL+yB+zXmT88ZugW20D3NtP5aaTTuPWij2qlYDTJQK9FGEf
1rW5mFZ4VkULEEHeO6MoJ/0t50Cs4ViA//Qz6Un4Z+zVqYjkItT5NNYx9j+czLIJ
KBre/ziJXu8yIxYaxqy4Lb4IepVL5T9/pjIw5nbNbWE+DfnfqiUPVifXx73gFRPZ
zRfgDD+Dbn/bbmDl137PkpPa2hk5CNUAL8/9rEhnjji2Lrb6SH+gFc0GvnZk7DJm
duKXhegU/ATZlI+1bLqL1D1z8Do6qQ==
=H9Qu
-----END PGP SIGNATURE-----
Merge remote-tracking branch 'remotes/alistair/tags/pull-riscv-to-apply-20201023' into staging
A collection of RISC-V fixes for the next QEMU release.
This includes:
- Improvements to logging output
- Hypervisor instruction fixups
- The ability to load a noMMU kernel
- SiFive OTP support
# gpg: Signature made Fri 23 Oct 2020 16:13:57 BST
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20201023:
hw/misc/sifive_u_otp: Add backend drive support
hw/misc/sifive_u_otp: Add write function and write-once protection
target/riscv: raise exception to HS-mode at get_physical_address
hw/riscv: Load the kernel after the firmware
hw/riscv: Add a riscv_is_32_bit() function
hw/riscv: Return the end address of the loaded firmware
hw/riscv: sifive_u: Allow specifying the CPU
target/riscv: Fix implementation of HLVX.WU instruction
target/riscv: Fix update of hstatus.GVA in riscv_cpu_do_interrupt
target/riscv: Fix update of hstatus.SPVP
hw/intc: Move sifive_plic.h to the include directory
riscv: Convert interrupt logs to use qemu_log_mask()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Initialize the object's values from the class when the object is
created, no need to have vl.c do it for us.
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Clean up vl.c, default min/max/default_cpus to uniprocessor
directly in the QOM class initialization code.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With upstream commit#ea1edcd7da1a "vl: relocate paths to data
directories", the data dir logic was unified between POSIX &
Win32. That patch moved to using 'get_relocated_path()', to
find the data dir. There is a latent bug in get_relocated_path
which can cause it to spin indefinitely, when the bind dir is
the same as the passed in dir (in this case, it was the data
dir).
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Message-Id: <SN4PR2101MB08802BF242C429A15DDB32ACC01B0@SN4PR2101MB0880.namprd21.prod.outlook.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
With upstream commit#8a19980e3fc4, logic was introduced to only
allow WHPX build on x64. But, the logic checks for the cpu family
and not the cpu. On my fedora container build, the cpu family is
x86 and the cpu is x86_64. Fixing the build break by checking for
the cpu, instead of the cpu family.
Signed-off-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Message-Id: <SN4PR2101MB0880D706A85793DDFC411304C01D0@SN4PR2101MB0880.namprd21.prod.outlook.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Since installation is not part of Makefiles anymore, Make need not
know the directories anymore. Meson already knows them through
built-in options, do everything using them instead of the config_host
dictionary.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Meson has a localedir option, so passing the path through that option
is the cleanest way when we move directories out of config-host.mak.
In preparation for doing that without changing semantics and without
special-casing localedir code, add a configure option.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The rules to build Makefile.mtest are suffering from the "tunnel vision"
problem that is common with recursive makefiles. Makefile.mtest depends
on build.ninja, but Make does not know when build.ninja needs to be
rebuilt before creating Makefile.mtest.
To fix this, separate the ninja invocation into the "regenerate build
files" phase and the QEMU build phase. Sentinel files such as
meson-private/coredata.dat or build.ninja are used to figure out the
phases that haven't run yet; however, because those files' timestamps
are not guaranteed to be touched, the usual makefile stamp-file trick
is used on top.
Reported-by: Havard Skinnemoen <hskinnemoen@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The HMP 'screendump' command generates Portable PixMap files.
Make it obvious by using the .ppm file extention.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201021105035.2477784-3-f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20201021105035.2477784-2-f4bug@amsat.org>
Tested-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Some of the "check-acceptance" tests are still skipped in the CI
since the docker images do not provide the necessary packages, e.g.
the netcat binary. Add them to get more test coverage.
Message-Id: <20201023073351.251332-5-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The tests are running in containers here, so it should be OK to
run with AVOCADO_ALLOW_UNTRUSTED_CODE enabled in this case.
Message-Id: <20201023073351.251332-4-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We are not running the acceptance tests on Travis anymore, so these
checks can be removed now.
Message-Id: <20201023073351.251332-3-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
The current URL on cdn.netbsd.org is failing - using archive.netbsd.org
instead seems to be fine.
Message-Id: <20201023073351.251332-2-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
generic-fuzz is not a standalone fuzzer - it requires some env variables
to be set. On oss-fuzz, we set these with some predefined
generic-fuzz-{...} targets, that are thin wrappers around generic-fuzz.
Do not make a link for the generic-fuzz from the oss-fuzz build, so
oss-fuzz does not treat it as a standalone fuzzer.
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201023150746.107063-18-alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
[thuth: Reformatted one comment to stay within the 80 columns limit]
Signed-off-by: Thomas Huth <thuth@redhat.com>
Prior to this, fuzzers in the output oss-fuzz directory were exactly
the same executable, with a different name to do argv[0]-based
fuzz-target selection. This is a waste of space, especially since these
binaries can weigh many MB.
Instead of copying, use hard links, to cut down on wasted space. We need
to place the primary copy of the executable into DEST_DIR, since this is
a separate file-system on oss-fuzz. We should not place it directly into
$DEST_DIR, since oss-fuzz will treat it as an independent fuzzer and try
to run it for fuzzing. Instead, we create a DEST_DIR/bin directory to
store the primary copy.
Suggested-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201023150746.107063-17-alxndr@bu.edu>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
We call get_generic_fuzz_configs, which fills an array with
predefined {name, args, objects} triples. For each of these, we add a
new FuzzTarget, that uses a small wrapper to set
QEMU_FUZZ_{ARGS,OBJECTS} to the corresponding predefined values.
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201023150746.107063-16-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Predefine some generic-fuzz configs. For each of these, we will create a
separate FuzzTarget that can be selected through argv0 and, therefore,
fuzzed on oss-fuzz.
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201023150746.107063-15-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
It can be useful to register FuzzTargets that have nearly-identical
initialization handlers (e.g. for using the same fuzzing code, with
different configuration options). Add an opaque pointer to the
FuzzTarget struct, so that FuzzTargets can hold some data, useful for
storing target-specific configuration options, that can be read by the
get_init_cmdline function.
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201023150746.107063-14-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Alexander Bulekov <alxndr@bu.edu>
Message-Id: <20201023150746.107063-13-alxndr@bu.edu>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Havard Skinnemoen
Hao Wu
Pavel Dovgalyuk
Thomas Huth
Richard Henderson
Philippe Mathieu-Daudé
Peter Maydell
Chen Qun
Stefan Reiter
Paolo Bonzini
Sunil Muthuswamy
Alexander Bulekov