(do_div): New function.
(insns): Accept UDIV and SDIV in ARM state.
(arm_cpus): The cortex-a15 option has all current v7-A extensions.
(arm_extensions): Add 'idiv' extension.
(aeabi_set_public_attributes): Update Tag_DIV_use values for the
Integer Divide extension.
* gas/doc/c-arm.texi: Document the idiv extension.
* gas/testsuite/gas/arm/armv7-a+idiv.d: New test.
* gas/testsuite/gas/arm/armv7-a+idiv.s: Likewise.
* gas/testsuite/gas/arm/attr-march-all.d: Update for Integer divide extension.
* gas/testsuite/gas/arm/attr-march-armv7-a+idiv.d: New test.
* include/opcode/arm.h (ARM_AEXT_ADIV): New define.
(ARM_ARCH_V7A_IDIV_MP_SEC): Likewise.
* opcodes/arm-dis.c (arm_opcodes): Support disassembly of UDIV and SDIV in
ARM state.
The Blackfin ISA is very exact with regards to address truncation when
under/over flowing its 32bit range. On a 32bit system, things work the
same and so addresses are decoded properly. On a 64bit system though,
the decoded addresses may include the bits that are supposed to have
been truncated. So force a 32bit truncation after the address has been
calculated.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Many register move insns were not being decoded properly, so rewrite
the whole function to be a bit more manageable in terms of valid
combinations.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin disassembler was originally based on the premise of parsing
valid opcodes all the time, so some of the opcode checking can be a bit
fuzzy. This is exemplified in decoding of parallel insns where many
times things are decoded as invalid when in reality, they may not be
used in parallel combinations. So add parallel checking to most insn
decoding routines so we see ILLEGAL and not just whatever insn happens
to be close to a valid mnemonic, as well as some additional sub-opcode
checks.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The push/pop multiple insn has a 3 bit field for the P register range,
but only values of 0...5 are valid (P0 - P5). There is no such P6 or
P7 register, so mark these insns as illegal.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The saturation bit was missed when decoding a vector shift insn
leading to the output looking the same as the non-saturating insn.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
All ASTAT bits work in the hardware even though they aren't part of the
official Blackfin ISA. So decode every ASTAT field to make the output
a bit nicer when working with hand generated opcodes.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Sometimes the encoding in the opcode is a 4 bit field which defines a
register number. However, register numbers are only 0-7, so make sure
we call illegal for when the opcode register number is greater than 8.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some extended registers when given to the DBG/DBGCMPLX pseudo insns are
not encoded properly. So fix them, fix the display of them when being
disassembled, and add testcases.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Support a few more ASTAT bits with the standard insns that operate on
ASTAT bits directly.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The disassembler has partial (but incomplete/broken) support already for
the pseudo debug insn OUTC, so let's fix it up and finish it. And now
that the disassembler can handle it, make sure our assembler can output
it too.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin ISA does not have a "SHIFT" insn, it has either LSHIFT,
ASHIFT, or BXORSHIFT. So be specific when disassembling.
As fall out of this change, we need to update some assembler tests.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
No need for these local structures related to formatting of output to
be writable, so constify the whole shebang.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* config/tc-arm.c (insns): Change MRC entry to accept APSR_RR instead
of just RR.
2010-09-17 Tejas Belagod <tejas.belagod@arm.com>
* gas/arm/copro.s: Add test for APSR_nzcv as a MRC operand.
* gas/arm/copro.d: Change pc in MRC to disassemble as APSR_nzcv. Also
add disassembly for test added in copro.s
2010-09-17 Tejas Belagod <tejas.belagod@arm.com>
* arm_dis.c (coprocessor_opcodes): Add MRC entry for APSR_nzcv.
* mips-opc.c (mips_builtin_opcodes): Add "sync_acquire",
"sync_mb", "sync_release", "sync_rmb" and "sync_wmb".
gas/testsuite/
* gas/mips/mips32r2-sync.d: New test for MIPS32r2 "sync"
instruction variants.
* gas/mips/octeon@mips32r2-sync.d: Likewise, Octeon version.
* gas/mips/mips32r2-sync.s: Source for the new test.
* gas/mips/mips.exp: Run the new test.
gas/testsuite/
2010-08-31 H.J. Lu <hongjiu.lu@intel.com>
PR binutils/11960
* gas/i386/opcode-intel.d: Updated.
* gas/i386/x86-64-opcode.d: Likewise.
* gas/i386/x86-64-opcode.s: Add a "pushw imm16" test.
opcodes/
2010-08-31 H.J. Lu <hongjiu.lu@intel.com>
PR binutils/11960
* i386-dis.c (sIv): New.
(dis386): Replace Iq with sIv on "pushT".
(reg_table): Replace T with {T|} on callT, JcallT, jmpT and JjmpT.
(x86_64_table): Replace {T|}/{P|} with P.
(putop): Add 'w' to 'T'/'P' if needed for Intel syntax.
(OP_sI): Update v_mode. Remove w_mode.
* rx.h (RX_Operand_Type): Add TwoReg.
(RX_Opcode_ID): Remove ediv and ediv2.
[opcodes]
* rx-decode.opc (SRR): New.
(rx_decode_opcode): Use it for movbi and movbir. Decode NOP2 (mov
r0,r0) and NOP3 (max r0,r0) special cases.
* rx-decode.c: Regenerate.
[sim/rx]
* rx.c (decode_cache_base): New.
(id_names): Remove ediv and edivu.
(optype_names): Add TwoReg.
(maybe_get_mem_page): New.
(rx_get_byte): Call it.
(get_op): Add TwoReg support.
(put_op): Likewise.
(PD, PS, PS2, GD, GS, GS2, DSZ, SSZ, S2SZ, US1, US2, OM): "opcode"
is a pointer now.
(DO_RETURN): New. We use longjmp to return an exception result.
(decode_opcode): Make opcode a pointer to the decode cache. Save
decoded opcode information and re-use. Call DO_RETURN instead of
return throughout. Remove ediv and edivu.
* mem.c (ptdc): New. Adds decode cache.
(rx_mem_ptr): Support it.
(rx_mem_decode_cache): New.
* mem.h (enum mem_ptr_action): add MPA_DECODE_CACHE.
(rx_mem_decode_cache): Declare.
* gdb-if.c (sim_resume): Add decode_opcode's setjmp logic here...
* main.c (main): ...and here. Use a fast loop if neither trace
nor disassemble is given.
* cpu.h (RX_MAKE_STEPPED, RX_MAKE_HIT_BREAK, RX_MAKE_EXITED,
RX_MAKE_STOPPED, RX_EXITED, RX_STOPPED): Adjust so that 0 is not a
valid code for anything.
* config/tc-ppc.c (ppc_set_cpu): Cast PPC_OPCODE_xxx to ppc_cpu_t
before inverting.
binutils/:
* ppc-dis.c (powerpc_init_dialect): Cast PPC_OPCODE_xxx to
ppc_cpu_t before inverting.
PR binutils/11676
* m68k-dis.c (print_insn_arg): Prefix float constants with #0e.
2010-06-16 Nick Clifton <nickc@redhat.com>
PR binutils/11676
* gas/m68k/pr11676.s: New test.
* gas/m68k/pr11676.d: Expected disassembly.
* gas/m68k/all.exp: Run the new test.
* config/tc-ppc.c (md_assemble): Emit APUinfo section for
PPC_OPCODE_E500.
gas/testsuite/
* gas/ppc/e500.s: Add eieio, mbar and lwsync
* gas/ppc/e500.d: Likewise.
include/opcode/
* ppc.h (PPC_OPCODE_E500): Define.
opcodes/
* ppc-dis.c (ppc_opts): Remove PPC_OPCODE_E500MC from e500 and
e500x2. Add PPC_OPCODE_E500 to e500 and e500x2
* ppc-opc.c (powerpc_opcodes): Deprecate all opcodes on EFS which
touch floating point regs and are enabled by COM, PPC or PPCCOM.
Treat sync as msync on e500. Treat eieio as mbar 1 on e500.
Treat lwsync as msync on e500.
Matthew Gretton-Dann
Mike Frysinger
Maciej W. Rozycki
Pierre Muller
H.J. Lu
Nathan Froyd
Alan Modra
DJ Delorie
Nick Clifton
Richard Earnshaw
Andreas Schwab