* monitor.c (monitor_debug): Move to utils.c, rename to puts_debug.
(monitor_write_memory, monitor_read_memory, monitor_insert_breakpoint,
monitor_remove_breakpoint): Remove useless address bits if current
monitor has MO_ADDR_BITS_REMOVE flag.
* monitor.h (MO_ADDR_BITS_REMOVE): Define.
* utils.c (puts_debug): Formerly monitor_debug from monitor.c;
move here and make public. Add better support for carriage returns.
* defs.h (puts_debug): Declare.
* dsrec.c (load_srec): Use puts_debug to print remotedebug information.
Output header record correctly.
(make_srec): Output a header record instead of a termination record
if sect is non-NULL (value is ignored), but abfd is NULL.
* config/mips/tm-tx39.h (DEFAULT_MIPS_TYPE): Remove definition.
(REGISTER_NAMES): Define to add R3900-specific registers.
* config/mips/tm-tx39l.h: Ditto.
* config/mips/tx39.mt (TDEPFILES): Add dve3900-rom.o and support files.
* config/mips/tx39l.mt: Ditto.
* m32r-tdep.c: Improved frame_chain and fn prologue analysis.
* configure.tgt: Add entry for m32r target.
* monitor.h: Add a flag to tell monitor_store_register to use
(val, regno) instead of (regno, val).
* monitor.c: Make monitor_store_register honor the above flag.
Make monitor_exp ignore DC1/DC3 for m32r.
Increase buf size in monitor_dump_regs.
* monitor.h,monitor.c:
Added monitor flags MO_NO_ECHO_ON_SETMEM (don't expect echo on
setmem command), MO_RUN_FIRST_TIME (if command to start process
running on target is different from one to continue execution),
MO_HEX_PREFIX (if addresses from monitor have a "0x" prefix).
* monitor.c,parse.c,sparc-tdep.c:
Don't require strings in the registers array. This is to allow
NULLs to be place holders in the tm-*.h file so that only minor
changes are needed when a new processor is introduced (eg, one
without floating point).
* sparc-tdep.c: Conditionally remove dependancies on floating point.
* sparclet-rom.c,config/sparc/sparclet.mt,config/sparc/tm-sparclet.h:
New files for target sparclet.
* symfile.c: Add option for 2nd parameter on load command : a load
offset added to the vma of each section.
with the obvious extension. (monitor_read_memory_single): Use
regexp for getmem.resp_delim because of parsing ambiguities caused
by certain monitors. (monitor_read_memory): Use new regexp stuff
to parse getmem.resp_delim.
* sh3-rom.c: Finish off table. Use new regexp capability for
getmem commands.
* monitor.c: Turn on caching.
(monitor_printf): If a ^C was sent, don't expect to see its
echo.
(monitor_open): Enable caching.
(monitor_resume, monitor_load): Flush cache.
(monitor_xfer_memory): Call cache routine.
(monitor_dump_regs): New.
(monitor_fetch_registers): If monitor_dump_regs available
then use it.
(monitor_load): Don't ref exec_bfd if it's NULL.
(monitor_load_srec): Use new monitor_make_srec calling convention.
(monitor_make_srec): Rewrite to cope with two, three and four byte
addresses.
* remote-hms.c (hms_cmds): Initialze end-of-command delim.
* dcache.h, dcache.h: Rewritten.
* remote.c: Reenable caching.
(getpkt): Reduce MAX_TRIES to 3.
(remote_xfer_memory): Use dcache_xfer_memory.
* defs.h (error_hook): New.
* top.c (error_hook): New definition.
* utils.c (error): Use error_hook if initialized.
* sparcl-tdep.c (HAVE_SOCKETS): Don't define if GO32 or WIN32. Use
HAVE_SOCKETS in place of #ifndef GO32.
error message to work with pre-ansi compilers.
(monitor_load_srec): reduced length of s-records from 128 to 32
bytes so download is more reliable with the rom68k monitor.
* rom68k-rom.c: Added trailing space to prompt string.
* config/i386/xm-i386sco.h (HAVE_STRSTR): Removed.
* config/i386/xm-go32.h, mswin/xm.h (SYS_SIGLIST_MISSING):
Removed.
* defs.h, config/{xm-lynx.h, xm-nbsd.h},
config/i386/{xm-i386bsd.h, xm-linux.h},
config/m68k/xm-hp300bsd.h, config/mips/xm-irix4.h,
config/ns32k/xm-ns32km3.h, doc/gdbint.texinfo
(PSIGNAL_IN_SIGNAL_H): Removed.
* Makefile.in (gdbtk.o): Use X11_CFLAGS to provide alternate
locations (per-host) for X11 include files.
* config/pa/hppahpux.mh (XM_CLIBS): Add -L/usr/lib/X11R5 to force
the use of R5 libs. (X11_CFLAGS): Add this to indicate the locs
of the R5 include files.
end-sanitize-gdbtk
* monitor.c monitor.h remote-est.c rom68k-rom.c: Add start of
support for interrupting target.
* monitor.c (monitor_open): Send stop command before doing
anything else.
* (monitor_load_srec): Fix record size calculation to prevent end
of segment from getting trashed.
* rom68k-rom.c: Update to latest version of struct monitor_ops.
* config/sparc/tm-sparc.h (FIX_CALL_DUMMY): Fix byte-order
problems. Makes DOS hosted function calling work.
* sparclite/crt0.s: Define _start to make COFF happy.
* testsuite/config/rom68k.exp (gdb_target_rom68k): Use
$targetname, $serialport and $baud instead of hardwired variables.
* testsuite/gdb.base/{sigall.exp signals.exp}: Skip these if the
target doesn't support signals.
Sun make (with VPATH) work...
* monitor.c monitor.h rom68k-rom.c: Serious cleanup to make IDP
(rom68k) target work right.
* array-rom.c op50-rom.c w89k-rom.c: Partial updates to new
monitor.c interface. More work needs to be done here.
* config/m68k/tm-monitor.h: Change DECR_PC_AFTER_BREAK to 0 to
match the IDP monitor. Also, set NUM_REGS to 18 cuz there's no
floating-point for this card.
to monitor config structure for supported baud rates for a target
and variable stop bits.
* monitor.c (monitor_fetch_register): Store register values in big
endian format on any host.
* monitor.c (monitor_load): check the load type and load the file
accordingly. Default to gr_load_image().
* monitor.c (monitor_load_ascii_srec): Load an ascii file in
srecord format by downloading to the monitor.
* w89k-rom.c, op50n-rom.c: set supported load types.
target.h, remote-es.c, remote-nindy.c: Don't set baud rate if
baud_rate is -1. Remove sr_get_baud_rate and sr_set_baud_rate;
just use the global variable itself. When printing baud rate,
don't print a baud rate if baud_rate is -1.
* Move target_signal_from_host, target_signal_to_host, and
store_waitstatus from inftarg.c to target.c. procfs needs them.
* target.c: Include "wait.h" and <signal.h>.
* target.h, infrun.c (proceed), proceed callers: Pass new code
TARGET_SIGNAL_DEFAULT instead of -1. This avoids problems with
enums being treated as unsigned and is cleaner.
* infrun.c (signals_info): Don't print TARGET_SIGNAL_DEFAULT or
TARGET_SIGNAL_0.
* infcmd.c (signal_command), infrun.c (signals_info):
Don't allow user to specify numeric equivalent of
TARGET_SIGNAL_DEFAULT.
struct target_waitstatus. Change status argument to target_wait to
be struct target_waitstatus * instead of int *.
* target.h, infrun.c, all targets: Change type of signal arguments
to resume(), proceed(), and target_resume() from int to enum
target_signal.
* All targets (*_wait, *_resume): Change accordingly.
* infcmd.c (program_info, signal_command), throughout infrun.c,
* fork-child.c, solib.c, hppa-tdep.c, osfsolib.c: Use this stuff.
* convex-xdep.c, convex-tdep.c: Add FIXME's (getting the Convex
signal code stuff right with the new signals would be non-trivial).
* inferior.h (stop_signal): Make it enum target_signal not int.
* target.c, target.h (target_signal_to_string, target_signal_to_name,
target_signal_from_name): New functions.
* inftarg.c, target.h (target_signal_to_host, target_signal_from_host,
store_waitstatus): New functions.
* procfs.c (procfs_notice_signals): Use them.
* i960-tdep.c (i960_fault_to_signal): New function, to replace
print_fault.
* config/i960/tm-i960.h: Don't define PRINT_RANDOM_SIGNAL.
* remote-mon.c: Remove commented out "set remotedebug" command.
* remote-nindy.c: Clean up comment about wanting alternative to
options specified on the GDB command line.
remote-mon.c (monitor_create_inferior), remote-nindy.c
(nindy_create_inferior), remote-st.c (st2000_create_inferior),
remote-vx.c (vx_create_inferior): Remove CREATE_INFERIOR_HOOK; it
is replaced by init_trace_fun.
* config/convex/xm-convex.h, convex-xdep.c: Add comments explaining
how to do without CREATE_INFERIOR_HOOK for whoever fixes the Convex
port.
* Makefile.in: Add Mach files to ALLDEPFILES, etc.
* m3-nat.c: Clean up more hair--message(), cprocs.
* configure.in: Recognize Mach targets and hosts.
* config/ns32k/tm-umax.h: Add some #ifndef's so tm-ns32km3.h can
include this file.
* Mach headers in config/*/tm-*.h: Fix includes to match correct
locations of files.
(bug_ops, monitor_desc): now static.
(monitor_desc): in several places, check and/or set to NULL.
* remote-hms.c (hms_files_info): Add the appropriate items where
missing in the printf call.
* remote-bug.c: new file for m88k bug support.
* config/m88k/m88k.mt (TDEPFILES): added remote-bug.o.
* Makefile.in (CLIBS): Reorder to make Lynx ld happy.
* (HFILES): New file thread.h.
* (OBS): New file thread.c.
* configure.in: Host config for Lynx/386.
* fork-child.c (fork_inferior): Call init_thread_list().
* infrun.c (resume): Add pid to invocation of target_resume().
* (wait_for_inferior): Pay attention to pid from target_wait().
Multi-threading code now uses this to determine what to do.
* inftarg.c (child_wait): Conditionalize based on CHILD_WAIT macro.
Use target_pid_to_str() macro throughout when printing pid.
* inferior.h (child_resume): Add pid to prototype.
* hppab-nat.c hppah-nat.c infptrace.c (child_resume): Pass in pid as
argument, instead of using inferior_pid.
* procfs.c (procfs_resume): Pass in pid as argument. Ignored for
now. Use target_pid_to_str() macro throughout for printing process id.
* remote-adapt.c (adapt_resume): Pass in pid as argument.
* remote-eb.c (eb_resume): Pass in pid as argument.
* remote-es.c (es1800_resume): Pass in pid as argument.
* remote-hms.c (hms_resume): Pass in pid as argument.
* remote-mips.c (mips_resume): Pass in pid as argument.
* remote-mm.c (mm_resume): Pass in pid as argument.
* remote-monitor.c (monitor_resume): Pass in pid as argument.
* remote-nindy.c (nindy_resume): Pass in pid as argument.
* remote-sa.sparc.c (remote_resume): Pass in pid as argument.
* remote-sim.c (rem_resume): Pass in pid as argument.
* remote-sp64sim.c (simif_resume): Pass in pid as argument.
* remote-st.c (st2000_resume): Pass in pid as argument.
* remote-udi.c (udi_resume): Pass in pid as argument.
* remote-vx.c (vx_resume): Pass in pid as argument.
* remote-z8k.c (rem_resume): Pass in pid as argument.
* remote.c (remote_resume): Pass in pid as argument.
* solib.c (solid_create_inferior_hook): Pass inferior_pid to
target_resume().
* target.c (normal_pid_to_str): New routine to print out process
ID normally.
* target.h (struct target_ops): Add pid to prototype at
to_resume(). (target_resume): Add pid argument.
* (target_pid_to_str): Default definition for normal type pids.
* thread.c, thread.c: New modules for multi thread/process control.
Mark Alexander
David Edelsohn
Michael Meissner
Michael Snyder
Dawn Perchik
Stan Shebs
Stu Grossman
Jeff Law
J.T. Conklin
Steve Chamberlain
Kung Hsu
Rob Savoye
Jim Kingdon
K. Richard Pixley